Part # 8011S datasheet

Part Manufacturer: Atmel

Atmel

Part Description: ATmega164P 324P 644P


Part Details:

Features· High-performance, Low-power AVR® 8-bit Microcontroller· Advanced RISC Architecture ­ 131 Powerful Instructions ­ Most Single-clock Cycle Execution­ 32 x 8 General Purpose Working Registers­ Fully Static Operation­ Up to 20 MIPS Throughput at 20 MHz­ On-chip 2-cycle Multiplier · High Endurance Non-volatile Memory segments ­ 16/32/64K Bytes of In-System Self-programmable Flash program memory­ 512B/1K/2K Bytes EEPROM 8-bit ­ 1/2/4K Bytes Internal SRAM­ Write/Erase Cycles: 10,000 Flash/ 100,000 EEPROM Microcontroller ­ Data retention: 20 years at 85°C/100 years at 25°C­ Optional Boot Code Section with Independent Lock Bits with 16/32/64K In-System Programming by On-chip Boot ProgramTrue Read-While-Write Operation ­ Programming Lock for Software Security Bytes In-System · JTAG (IEEE std. 1149.1 Compliant) Interface ­ Boundary-scan Capabilities According to the JTAG Standard Programmable ­ Extensive On-chip Debug Support­ Programming of Flash, EEPROM, Fuses, and Lock Bits through the JTAG Interface Flash · Peripheral Features ­ Two 8-bit Timer/Counters with Separate Prescalers and Compare Modes­ One 16-bit Timer/Counter with Separate Prescaler, Compare Mode, and Capture Mode­ Real Time Counter with Separate Oscillator­ Six PWM Channels ATmega164P/V ­ 8-channel, 10-bit ADC Differential mode with selectable gain at 1x, 10x or 200x ATmega324P/V ­ Byte-oriented Two-wire Serial Interface­ Two Programmable Serial USART ATmega644P/V ­ Master/Slave SPI Serial Interface­ Programmable Watchdog Timer with Separate On-chip Oscillator­ On-chip Analog Comparator­ Interrupt and Wake-up on Pin Change Preliminary · Special Microcontroller Features ­ Power-on Reset and Programmable Brown-out Detection­ Internal Calibrated RC Oscillator­ External and Internal Interrupt Sources Summary ­ Six Sleep Modes: Idle, ADC Noise Reduction, Power-save, Power-down, Standby and Extended Standby · I/O and Packages ­ 32 Programmable I/O Lines­ 40-pin PDIP, 44-lead TQFP, 44-pad QFN/MLF (ATmega164P/324P/644P)­ 44-pad DRQFN (ATmega164P) · Operating Voltages ­ 1.8 - 5.5V for ATmega164P/324P/644PV­ 2.7 - 5.5V for ATmega164P/324P/644P · Speed Grades ­ ATmega164P/324P/644PV: 0 - 4MHz @ 1.8 - 5.5V, 0 - 10MHz @ 2.7 - 5.5V­ ATmega164P/324P/644P: 0 - 10MHz @ 2.7 - 5.5V, 0 - 20MHz @ 4.5 - 5.5V · Power Consumption at 1 MHz, 1.8V, 25°C for ATmega164P/324P/644P ­ Active: 0.4 mA­ Power-down Mode: 0.1µA­ Power-save Mode: 0.6µA (Including 32 kHz RTC) 8011JS­AVR­09/08 1. Pin Configurations 1.1 Pinout - PDIP/TQFP/QFN/MLF Figure 1-1. Pinout ATmega164P/324P/644P PDIP (PCINT8/XCK0/T0) PB0 PA0 (ADC0/PCINT0) (PCINT9/CLKO/T1) PB1 PA1 (ADC1/PCINT1) (PCINT10/INT2/AIN0) PB2 PA2 (ADC2/PCINT2)


Please click the following link to download the datasheet:

8011S.pdf Datasheet